Yamaha Raptor Forum - View Profile: 03LimitedEditionRaptor

03LimitedEditionRaptor 03LimitedEditionRaptor is offline

Senior Member

  Visitor Messages

Showing Visitor Messages 1 to 3 of 3
  1. emmacoggins
  2. yamahaneday
    03-11-2012 12:30 PM - permalink
    yamahaneday
    Hey I dont know if you remember you posted on my thread about Hard time starting... you said "That is how my raptor would start when I removed the decompression mechanism at around 50 deg. Get it down to 30 deg and you wouldnt get it to start."
    Could you help me out by telling me a little bit more?
  3. redneckRaPtor660
    01-11-2011 05:40 PM - permalink
    redneckRaPtor660
    i glad too see some one knows how to respect the trails

  About Me

  • About 03LimitedEditionRaptor
    Location
    Nebraska
    Interests
    ATV's, RC's, Music
  • Signature
    2003 Limited Edition Raptor
    Kenz 720cc 11:1 stroker, +1 valves, Mega Cycle X-4 Cam, Sparks 6x Big Core, Keihin 35mm FCR's. 158 mains, 52 pilots, fuel screws 2 turns out.

    97 Banshee
    F.A.S.T. Dune Ported 4mill, CPI Inframes, Keihin PWK33's, Direct Drive Lockup. 158 mians, CEL needles second clip, #48 pilots, air scews 2.0 turns out.

  Statistics

Visitor Messages
General Information
  • Last Activity: 05-20-2019 09:14 PM
  • Join Date: 06-21-2006
  • Referrals: 0

  Friends

Showing Friends 1 to 3 of 3
  • Bigdaddy660R
    • Bigdaddy660R is offline
  • DEZPERADO
    • DEZPERADO
    • I may be getting older, but I refuse to grow up!
    • DEZPERADO is offline
  • redneckRaPtor660
    • redneckRaPtor660 is offline

  Mentions

No results to display...

  Quotes

03-14-2019
12:11 PM - bulldogz440 quoted 03LimitedEditionRaptor in post Revs in neutral - falls on face when riding. Reverse rev limiter?
Where the carbs that were on it Genuine Mik...
01-16-2019
06:56 PM - bridgeport13b quoted 03LimitedEditionRaptor in post burned clutch need help
Ok, SO clutch material in oil generally doe...
01-15-2019
02:23 PM - 03LimitedEditionRaptor quoted bridgeport13b in post burned clutch need help
Ok, SO clutch material in oil gene...
01:48 PM - 03LimitedEditionRaptor quoted Skuffknee in post Bike won't rev; PB and rev limit mod'd
The needles are clip style adj...
12-03-2018
01:00 PM - Rprice quoted 03LimitedEditionRaptor in post 660R 2004 intake maintenance
Well hopefully you don't buy the stock repl...
10-06-2018
03:58 PM - 03LimitedEditionRaptor quoted BoxerBoss in post 01 660R Mid Range issue.. Detailed description
What tool are you guys using t...
10-04-2018
03:08 PM - BoxerBoss quoted 03LimitedEditionRaptor in post 01 660R Mid Range issue.. Detailed description
Sounds like it needs a timing chain by the ...
09-28-2018
11:32 PM - 03LimitedEditionRaptor quoted RaptorID in post Big 3 Jetting Question
Good point! I swapped all the...
11:21 PM - RaptorID quoted 03LimitedEditionRaptor in post Big 3 Jetting Question
Chinese needle and seat rubber tip might ha...
01:10 PM - 03LimitedEditionRaptor quoted RaptorID in post Big 3 Jetting Question
This is so weird, I finally g...
09-22-2018
07:42 AM - 850xpeps quoted 03LimitedEditionRaptor in post 03 660 trans mission issues
Does this slippage happen in any other gear...
09-21-2018
10:18 PM - 03LimitedEditionRaptor quoted Jason Compton in post 11.1 piston
With the help of my son when I was...
12:00 PM - 03LimitedEditionRaptor quoted RaptorID in post Big 3 Jetting Question
Most of the parts came in yes...
11:14 AM - RaptorID quoted 03LimitedEditionRaptor in post Big 3 Jetting Question
At 5000ft Id probably start out at 144/146 ...
09-18-2018
10:11 PM - 03LimitedEditionRaptor quoted RaptorID in post Big 3 Jetting Question
Thanks for the info! I have t...
08:57 PM - RaptorID quoted 03LimitedEditionRaptor in post Big 3 Jetting Question
That could be part of your problem them. Ch...
03:30 PM - 03LimitedEditionRaptor quoted RaptorID in post Big 3 Jetting Question
I bought the AllBalls rebuild...
12:09 AM - RaptorID quoted 03LimitedEditionRaptor in post Big 3 Jetting Question
what all was done when you rebuilt the carb...
09-16-2018
12:01 AM - 03LimitedEditionRaptor quoted or.stater in post Umm, this doesn't look good!
It looks like they didnt adjus...
09-15-2018
02:21 AM - or.stater quoted 03LimitedEditionRaptor in post Umm, this doesn't look good!
They don't stay tight and slowly walk back ...
 
For the best viewing experience please update your browser to Google Chrome